Netopia 3300 Bedienungsanleitung Seite 28
- Seite / 334
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-12 Firmware User Guide
6. Toggle or enter your IP Parameters.
For more information, see:
• “IP Setup” on page 7-2
• “Network Address Translation (NAT)” on page 3-2
• “Stateful Inspection Options” on page 3-8
• “Filter Sets” on page 3-2
• The RIP Profile Options selection displays the RIP Profile Parameters screen.
IP Profile Parameters
Address Translation Enabled: Yes
IP Addressing... Numbered
NAT Map List... Easy-PAT List
NAT Server List... Easy-Servers
NAT Options...
Stateful Inspection Enabled: No
Local WAN IP Address: 0.0.0.0
Local WAN IP Mask: 0.0.0.0
Filter Set...
Remove Filter Set
RIP Profile Options...
Return/Enter to select <among/between> ...
Configure IP requirements for a remote network connection here.
RIP Profile Parameters
+-----------------------+
+-----------------------+
Receive RIP: | Off |
| v1 |
| v2 |
| Both v1 and v2 |
| v2 MD5 Authentication |
+-----------------------+
- Copyright 2
- Part Number 2
- Firmware User Guide 10
- Introduction 11
- Telnet-based Management 12
- Netopia Telnet Menus 12
- Netopia Models 13
- Configuring Telnet software 14
- 1-6 Firmware User Guide 16
- WAN Configuration 17
- ADSL Line Configuration screen 20
- ATM Circuit Configuration 21
- PPPoE/PPPoA Autodetection 29
- Advanced Connection Options 31
- Scheduled Connections 32
- Viewing scheduled connections 33
- Adding a scheduled connection 34
- Set Weekly Schedule 35
- Set Once-Only Schedule 36
- Backup Configuration 37
- Diffserv Options 38
- Priority Queuing (TOS bit) 41
- 2-28 Firmware User Guide 44
- Filter Sets 46
- Stateful Inspection 47
- Add Exposed Address List 48
- System Configuration 3-5 49
- Exposed Address Associations 52
- VLAN Configuration 55
- Adding a RADIUS Profile 57
- Adding Port interfaces 60
- Changing or Deleting a VLAN 62
- System Configuration 3-19 63
- 3-20 Firmware User Guide 64
- System Configuration 3-21 65
- Date and time 66
- Wireless configuration 67
- Wireless Multimedia (WMM) 69
- Enable Privacy 70
- Multiple SSIDs 74
- System Configuration 3-31 75
- MAC Address Authentication 77
- Console Configuration 79
- Upgrade Feature Set 80
- Router/Bridge Set 81
- Log event dispositions 87
- Install via the Console menu 92
- Set up NTP 94
- Set up Syslog 94
- 3-52 Firmware User Guide 96
- Chapter 4 97
- Features 98
- Dynamic mapping 99
- WAN Network 100
- LAN Network 100
- Supported traffic 101
- MultiNAT Configuration 102
- System Configuration 103
- NAT rules 105
- Add Map 106
- Modifying map lists 108
- 4-14 Firmware User Guide 110
- Adding Server Lists 111
- Modifying server lists 114
- Deleting a server 116
- IP profile parameters 118
- IP Parameters 120
- NAT Associations 122
- IP Passthrough 124
- First Come First Serve Mode 126
- A restriction 127
- MultiNAT Configuration Example 128
- Notes on the example 131
- Chapter 5 133
- Transit Internetwork 134
- About PPTP Tunnels 136
- About IPsec Tunnels 139
- About L2TP Tunnels 140
- About GRE Tunnels 143
- VPN force-all 146
- About ATMP Tunnels 147
- Encryption Support 149
- ATMP/PPTP Default Profile 150
- VPN QuickView 152
- Dial-Up Networking for VPN 153
- PPTP example 157
- ATMP example 160
- 5-30 Firmware User Guide 162
- GRE as shown below 163
- Windows Networking Broadcasts 164
- Management for VPNs 167
- Adding an IKE Phase 1 Profile 170
- Advanced IKE Phase 1 Options 173
- Key Management 177
- Advanced IPsec Options 180
- Enhanced Dead Peer Detection 181
- Multiple Network IPsec 182
- IPsec Manual Key Entry 188
- VPN Quickview 189
- 6-26 Firmware User Guide 192
- IP Setup 193
- IP subnets 196
- Static routes 198
- Viewing static routes 199
- Adding a static route 200
- Modifying a static route 201
- Deleting a static route 201
- RIP Options 202
- IP Setup 7-11 203
- 7-12 Firmware User Guide 204
- Transmit RIP 204
- Adding a key 205
- Changing or deleting a key 206
- IP Address Serving 209
- IP Address Pools 212
- DHCP NetBIOS Options 213
- More Address Serving Options 215
- DHCP Relay Agent 220
- Connection Profiles 222
- Multicast Forwarding 225
- Additional LANs 229
- Editing or Deleting ALANs 232
- Line Backup 233
- Line Backup 8-3 235
- Backup Configuration screen 241
- Backup Default Gateway 246
- IP Setup screen 248
- Backup Management/Statistics 249
- QuickView 250
- Monitoring Tools 251
- General status 252
- Current status 252
- Statistics & Logs 253
- Event Histories 254
- Device Event History 255
- IP Routing Table 256
- General Statistics 256
- Physical Interface 257
- Network Interface 257
- System Information 258
- The SNMP Setup screen 259
- Community strings 260
- SNMP traps 261
- Setting the IP trap receivers 262
- Viewing IP trap receivers 263
- Modifying IP trap receivers 263
- Deleting IP trap receivers 263
- 9-14 Firmware User Guide 264
- Security 265
- UPnP Support 266
- Superuser configuration 267
- Limited user configuration 268
- Security 10-5 269
- Advanced Security Options 270
- RADIUS server authentication 271
- TACACS+ server authentication 272
- Warning alerts 273
- 10-10 Firmware User Guide 274
- User access password 276
- User menu differences 277
- WAN Configuration screens 278
- System Configuration menu 280
- IP Setup menu 280
- Statistics & Logs menu 281
- 10-18 Firmware User Guide 282
- Quick Menus 283
- Telnet Access 284
- About Filters and Filter Sets 285
- How individual filters work 286
- A filtering rule 287
- Parts of a filter 287
- Port numbers 287
- Port number comparisons 288
- Other filter attributes 288
- Putting the parts together 289
- Filtering example #1 290
- Filtering example #2 290
- Design guidelines 291
- Adding a filter set 293
- Adding filters to a filter set 294
- Viewing filters 296
- Modifying filters 296
- Deleting a filter set 297
- A sample filter set 297
- Possible modifications 299
- TOS field matching 301
- Firewall Tutorial 303
- Firewall design rules 304
- Binary representation 305
- Logical AND function 305
- Implied rules 305
- Filter basics 306
- Example network 307
- Example 1 307
- Example 2 308
- Example 3 308
- Example 4 309
- Example 5 309
- Configuration Management 310
- 10-50 Firmware User Guide 314
- Utilities and Diagnostics 315
- Trace Route 318
- Telnet Client 319
- Factory Defaults 320
- Updating firmware 321
- Downloading configuration files 321
- Restarting the System 322
- 11-10 Firmware User Guide 324
- Troubleshooting 325
- Network problems 326
- Power Outages 327
- Technical Support 327
- How to reach us 328
Verwandte Produkte und Handbücher für Hardware Netopia 3300
Hardware Netopia 4686-XL Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Hardware Netopia 3356(EU Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Hardware Netopia R910 Bedienungsanleitung
(209 Seiten)
(209 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern